CALL CENTER :  +66-38-627-800
 
 

QUALITY EXCELLENCE

The product quality control is a critical mission of Mitsui Siam Components Co.,Ltd.. We continue to focus and control our products to meet the customer requirements, IATF16949, ISO14001 and OHSAS18001 standards.  Mitsui Siam Components Co.,Ltd. has won the trust of customers all along with our modern laboratory, technologies of machine, experience, expertise and attention to get high quality products.



Coordinate Measuring Machine (CMM)

CMMs will be used to confirm the dimension of part and product at initial production start, every time of initial change and monthly .period

Our CMM’s range is
X: 900 mm,
Y: 1000 mm,
Z: 600 mm
Resolution is 0.0005 mm.

Our CMMs are conform to ISO 10360-2:2009, 10360-5:2010




Operation Force Testing


This test methods to determine the forces to open/close doors and to engage/release and lock/unlock the hardware using a key or handle which concern with door lock’s function and safety of end user.

We’re perform period testing at initial production and monthly period and also when have any changes during manufacturing.

Testing machine is conform to ISO 376:2004, ISO 7500-1:2004.




Strength Testing

To determine the strength of material and product such as strength of welding and rivet which majority concern to the safety of end user.We’re perform period testing at initial production and monthly period and also when have any changes during manufacturing.Testing machine is conform to ISO 376:2004, ISO 7500-1:2004.





Microscope Measuring


To measure in focused area for inspection and analysis the surface of part, pitch of thread, bent angle of stamping part, etc. for further improvement.

We’re use microscope to confirm the quality of part at initial production and monthly period and also when have any changes during manufacturing.

Microscope’s resolution is 0.0005 mm. and conform to JIS B 7153:1995.





Contour and Roughness Measuring


Used to measure the surface roughness of various work piece such as plane, tilt, inner bore, deep recess etc.

We’re using to confirm the quality of single part and plating part at initial production and every lot of mass production and when have any change during manufacturing.

Conform to JIS B 0651 (2001).




Environment Testing


A chamber can be used:
  1. As a stand-alone test for environmental effects on test specimens.
  2. As preparation of test specimens for further physical tests or chemical tests.
  3. As environmental conditions for  conducting testing of specimens.
Our test range is -40c up to +110c. and maximum humidity at 95%.




Hardness Testing


To determine metal part’s hardness.

Our lab can test both Rockwell Scale B (HRB) and Rockwell Scale C (HRC)

We’re perform period testing at initial production and monthly period and also when have any changes during manufacturing.

Both testing machine are conform to JIS B 7726:2010.




Durability Testing

To guarantee durability of our product, we’re perform simulation test of door lock and back door’s functioning.

We’re perform period testing at initial production and also when have any changes during manufacturing.

Cycle of testing is 100,000 – 200,000 times continuous per once.





Salt Spray Testing

Test method used to check corrosion resistance of coated samples.
Salt spray test is an accelerated corrosion test that produces a corrosive attack to the coated samples in order to predict its suitability in use as a protective finish.
The appearance of corrosion products (oxides) is evaluated after a period of time.

We’re perform period testing at initial production and also when have any changes during manufacturing.

Our test is conform to ASTM B 117, JIS Z 2371 and ISO 9227.




Quality – Real time Assessment Management System (Q-RAMS)


Real time measurement and monitoring for part stamping and injection.

Defective part will easily detect and alert to concern section to gathering with solution on time.

We’re using to confirm the quality of single part at initial, middle and end of lot production.

We’re implement this system to ensure our product is meet customer’s requirement and satisfaction.

 
 
  MITSUI SIAM COMPONENTS CO., LTD.
60/8 M.3 T.Mabyangporn A. Pluakdaeng, Rayong 21140 Thailand.
Tel. +66-38-627-800, Fax. +66-38-015-071
Copyright © 2015 MITSUI SIAM COMPONENTS CO., LTD. All Rights Reserved.